C210AHP Hollow Pin Conveyor Chain

Configure C210AHP for the conveyor, not only the chain code

C210AHP Hollow Pin Conveyor Chain should be checked with sprocket pitch, rail contact, carrier underside, strand spacing, drive layout and operating environment. For replacement work, send the installed model, measured pitch, sprocket details and clear side/end photographs. For new equipment, send carrier mass, line speed, carrier count, start/stop sequence and station interfaces.

请求工程报价

C210AHP is a Type B hollow-pin conveyor chain with a specified pitch of 31.75 mm. The hollow-pin construction provides an open bore through the chain pin, giving machine builders a defined location for cross rods, fixtures or other application-specific elements when the complete conveyor design requires them. That flexibility is especially useful in custom pallet handling, indexing fixtures and conveying systems where the chain must carry or locate more than a plain flat load. The table below preserves the technical data bore, pin, plate, pitch, tensile and mass values for this exact model. Any cross-rod diameter, attachment geometry or load carried by those attachments should be confirmed separately when those application-specific parts are not stated in the technical table.

The dimensional row gives a precise starting point, but the surrounding conveyor hardware determines how those dimensions function in service. The 31.75 mm pitch must align with the sprocket, while the hollow bore d4 of 5.12 mm defines the minimum catalogue opening through the pin. The technical table lists a minimum tensile strength of 20.4 kN and a chain mass of 0.76 kg/m. Neither number defines the permissible load on a custom cross rod; that attachment must be engineered from its own material, diameter, support span, loading direction and connection method. In the selected family, C210AHP sits between C210ALHP and C212ALHP by pitch. That makes it a useful mid-range reference, but each adjacent model has its own roller, pin and plate geometry, so dimensions should be checked row by row. For replacement work, measure the bore and the plate stack as carefully as the pitch because two chains with a similar overall appearance can have different attachment clearances.

尺寸图

请将此图与模型表配合使用。节距、滚轮、销轴和板的符号只有与相应的视图匹配才有意义。

Exact technical data for C210AHP

本页所有数值均取自该车型技术数据中对应的车型数据行。技术数据中未明确列出的字段，特意未填充估算值。

确认更换订单前，应对照图纸核对尺寸。P、d1、d2、d4、d8、b1、b2、L、Lc、h2、T 和 t 等符号均指该系列链条对应的产品目录图纸。

这条链条在托盘输送机中的位置

托盘输送链必须与整个输送路径协同工作。链条与链轮啮合，沿着导轨或耐磨轨道运行，支撑或驱动托盘或工件通过指定的滚轮界面，然后返回下方的输送带。托盘或工件可能还会遇到挡块、定位器、升降装置、传送装置、传感器和加工工位。因此，即使链条型号正确，如果导轨未对准、链轮齿形与链条不匹配，或者托盘或工件接触到错误的滚轮表面，输送性能仍然可能不佳。

Current conveyor-system terminology commonly describes pallet transport in terms of workpiece carriers, buffering, positioning, separation, locating stations, stops, merges and transfers. Those functions are system-level features. C210AHP should therefore be selected from its specified geometry first, then checked against the required conveyor function. EVER POWER does not treat a catalogue tensile value or a family description as a substitute for a system calculation.

How to select C210AHP

对于新安装的输送机，首先要确定工件托架和所需的生产顺序，然后逐步扩展到链条路径。对于更换的输送机，则要从已安装的链条入手，测量机器上实际安装的链条。无论哪种情况，目标都是在生产或发货前消除所有不确定性。

1. 确认确切的螺距，并比较与链轮、导轨、托盘或附件硬件连接的每个尺寸。
2. 确定链条股数、股间中心距、输送机长度、驱动装置和张紧方式。
3. Specify the cross rod or attachment concept, required bore clearance, rod material, support span and the direction in which the attachment is loaded.
4. 提供托盘或工件载体的质量以及传送带上一次可能放置的托盘数量；不要仅根据抗拉强度来确定尺寸。
5. 描述启动/停止频率、加速度、索引、任何累积或硬停止站，以及是否可能发生冲击载荷。
6. 说明操作环境，包括温度、灰尘、湿度、清洁剂和润滑限制。
7. 对于更换工作，请提供链轮齿数、孔径/轮毂详细信息以及照片或图纸，以便检查链条与链轮的匹配情况。

当两款型号在照片中看起来相似时，请使用尺寸表和图纸来区分它们。销轴长度、滚轮直径或链板厚度的差异都可能导致与导轨干涉、与链轮错位或托盘接触不良。如果已安装链条的尺寸与尺寸表不符，请在询价时提供这些差异，而不是强行选择最接近的型号。

链轮、轨道和输送机集成

链条和链轮的选择应同时进行。链轮节距必须与链条节距相匹配，而齿形、齿数、孔径、轮毂布置和轴连接方式则取决于机器设计。未经检查磨损情况就重复使用旧链轮会缩短新链条的使用寿命。反之，即使齿距正确，仅凭照片订购新链轮也可能导致孔径或轮毂不匹配。

系统的轨道侧同样需要关注。检查材料、直线度、过渡段、接头、回程导轨以及所有与滚轮接触的表面的垂直位置。托盘挡块和定位装置应能停止或定位托架，而不会使链条发生侧向位移。在多股输送机中，应保持各股链条对齐并张紧，以防止一侧将托盘拉到另一侧前面。对于较长的系统，应记录收紧行程以及用于保持链条长度和跟踪的方法。

EVER POWER 可根据客户的具体要求，提供配套链轮和链条的整套报价。此处提及配套链轮，是因为它是链条的功能性搭档；链轮的孔径、齿数或轮毂尺寸并非仅根据链条型号推断得出。

安装和维护检查点

调试期间，检查链条进出各链轮时是否无侧向载荷，以及支撑导轨是否与预定的滚子接触面对齐。在机器投入自动运行前，确认连接链节、固定件和所有链条专用附件均已完全安装到位。安装双股输送机时，保持两侧同步，以防止托盘以一定角度进入工位。

Inspect the hollow pins and inserted rods or fixtures as separate interfaces. Fretting, bent rods, loose retainers or contact between a rod and the pin bore can indicate an attachment-design or alignment issue even when the base chain remains serviceable. Establish an inspection interval from the real duty cycle rather than using one universal schedule. A line that indexes continuously, operates in abrasive contamination or experiences frequent pallet stops may need more frequent checks than a lightly used transfer conveyor. Record elongation, roller condition, unusual noise, hot spots, sprocket wear and any recurring tracking correction so maintenance decisions are based on trend rather than guesswork.

润滑方式应根据链条结构、环境和工艺限制而定。切勿仅仅因为同一台机器上的另一条链条使用某种润滑剂就照搬。如果输送机在敏感产品、清洁剂、高温环境或限制润滑油的工艺流程附近运行，请在询价单中说明这些情况，以便讨论合适的链条和维护方案。

定制和询价信息

For an RFQ on C210AHP, send the chain model if known, required quantity or length, destination country, machine application, conveyor speed, pallet or carrier details and any available drawing. Include the proposed rod or attachment drawing and the required clearance through the hollow pin. If the request is a replacement for an installed chain, photographs of the complete chain, a close-up of one pitch, the sprocket and the rail interface are especially useful. EVER POWER can review the dimensional match and quote chain together with matching sprocket requirements when the sprocket data are available. Where the technical data do not define a property – for example a special material grade, attachment load, permissible working load or a particular coating – that property will be treated as an RFQ confirmation item rather than being assumed from the model family.

为了便于生产计划，请说明您需要的是连续匹配长度的链条、散装链条、连接链节、备用链节还是链轮。如果输送机使用成对链条，请告知是否需要匹配的链段长度。如果图纸包含技术规格表中未列出的公差或特殊接口，请将其附在询价单中。这些信息比笼统地询问“托盘输送链”更有用，因为它能确保报价与实际使用该部件的机器紧密相关。

常见问题解答

下单前请先发送链数据。

请以本页的模型和表格为起点，然后将您的输送机图纸、所需数量或长度、目的地国家/地区以及任何更换链条的尺寸发送至 [email protected]。对于改造项目，请提供链轮和导轨接口，以便审核涵盖整个链条路径，而不仅仅是链条本身。

索取报价

链结构和机械界面

工作接口包括销轴、衬套、滚轮、侧板和特定系列的支撑结构。钢轨应支撑预期的滚轮表面，且不应迫使侧板承受轨道载荷。链轮必须属于同一节距系统，且链轮架应仅与预期支撑表面接触。不对中可能表现为噪音、边缘磨损、铰接僵硬或钢绞线间载荷分配不均。

托盘和工件搬运车的应用集成

该系列产品适用于托盘式装配、检验、搬运和缓冲等应用场景，在这些场景中，可重复的载体运动至关重要。协调挡块、升降装置、定位器、传感器和搬运装置，使工艺载荷通过夹具传递，而不是转化为意外的链条侧向载荷。累积或自由流动行为是系统层面的结果。

制造和检验点

订单放行时应检查节距一致性、辊轮和销轴几何形状、板材对齐情况、铰接性能、表面状况以及与输送机连接的型号尺寸。如果需要材料证书、检验报告或订单特定的合规文件，请在接受订单前在询价单中列出。

商业规划、样品和文档

What to send for a C210AHP quotation

参考 C210AHP 并附上输送机图纸或标明链条路径、链轮、导轨接触面和托架接口的标记照片。请注明数量、更换/新设计状态、环境、所需文件和交货时间。如果代码不确定，请提供多个接头的测量节距和侧视图照片。

Send C210AHP RFQ