Pallet conveyor chain family

Rantai Penggelek Sisi

Compare product configurations, machine interfaces and operating duty before selecting a model.

Product family

Side Roller Chains for pallet and workpiece-carrier conveyors

Side Roller Chains place rollers outboard of the chain body so the chain can run or be supported against defined side rails. The side-roller position changes how load enters the chain and how the conveyor tracks, so rail geometry and sprocket clearance are important selection inputs.

Family configuration

The category includes polyacetal side-roller, double-pitch side-roller and stainless side-roller configurations. Choose by exact pitch, side-roller diameter and location, plate geometry, rail contact and environment rather than by overall appearance.

Start with the conveyor function and carrier interface, then compare the model drawing. For replacement work, use measured dimensions from the installed chain and sprocket rather than a visual match.

Side Roller Chains representative chain product

Machine interfaces to confirm before model selection

Pitch and strand geometry

Measure several pitches, confirm strand spacing and note whether the conveyor uses matched parallel strands. Record the installed sprocket tooth count and bore so engagement can be checked.

Roller and rail contact

Identify which roller or chain surface carries the load, rail width and material, return support and any side guide. Photograph the contact area when the conveyor is an existing machine.

Carrier underside

Record the pallet contact surfaces, wear strips, locating features, center of gravity and any lift or transfer mechanism that changes how the carrier is supported.

Duty and environment

State conveyor speed, starts per hour, accumulation time, maximum queue, contamination, temperature, lubrication constraints and maintenance access.

Side Roller Chains structure and interface drawing

Use the drawing to close the dimensional match

Model selection should move from system requirements to the exact chain geometry. Compare pitch, roller diameters and positions, pin diameter and length, plate height and thickness, and any special attachment or hollow-pin feature shown on the drawing. A match on pitch alone is not enough to approve interchangeability.

When dimensions are missing from an old machine record, measure the installed chain over several joints to reduce single-joint error, then add side and end photographs. If the sprocket is worn or is being replaced at the same time, include its tooth count, bore and hub arrangement in the review.

Applications and operating duty

Side Roller Chains may be considered for palletized assembly, inspection, workpiece transfer, accumulation or machine-tending layouts when the chain architecture matches the rail and carrier design. The application name does not by itself confirm a model.

Describe loaded carrier mass, conveyor length, line speed, start/stop frequency and the number of carriers that can occupy the line. For accumulation, state queue length and release sequence. For locating or machining stations, identify the device that supports process forces so those loads are not unintentionally transferred through the conveyor chain.

Side Roller Chains pallet conveyor application

Aliran kerja pemilihan

StepDecisionInformation to provide
1Define the carrier pathLoaded mass, pallet underside, stations, accumulation zones and transfers.
2Confirm chain/rail interfacePitch, roller arrangement, strand spacing, rail section and return support.
3Confirm drive interfaceSprocket tooth count, bore, drive position, take-up and shaft alignment.
4Check duty and environmentSpeed, starts, queue behavior, temperature, contamination and lubrication limits.
5Confirm the selected modelExact product drawing, quantity, documentation and delivery requirement.
Practical selection

Use an end view to confirm the running interface

Side-roller chains are difficult to identify reliably from a side photograph alone. An end view shows the roller offset, its relationship to the chain body and the rail surface that carries or guides it. Measure the side-roller diameter, centerline position, lateral clearance, rail width and height, and strand spacing. Include transfer points where the roller moves from one rail section to another because a small step or gap can create impact that is not obvious on a stationary conveyor.

During commissioning, run representative loaded carriers through the complete loop and observe the side roller at rail joints, sprockets and transfers. Look for edge loading, rubbing of chain plates and unequal contact between parallel strands. If those symptoms appear, correct rail and carrier geometry before increasing chain tension. A well-matched chain cannot compensate for a guide system that forces the roller sideways.

Record the installed interface and operating duty in the enquiry so dimensional fit and application suitability can be confirmed separately.

Commissioning and maintenance checks

After installation, run the line slowly without load and watch chain entry and exit at the sprockets, rail transitions, take-up travel and carrier tracking. Add representative pallets and confirm roller rotation, stop/release behavior and transfers before raising speed. Uneven tracking, scuffing, chain climbing, impact at transfers or different tension between parallel strands should be corrected before normal production use.

Maintenance should trend elongation over a defined number of pitches, roller condition, plate wear, rail wear, sprocket tooth condition and take-up position. Record the same measurement points each time so changes can be compared rather than relying on a single visual inspection.

FAQ and RFQ preparation

Can a visually similar chain be substituted?

Not on appearance alone. Compare the complete dimension set and the installed sprocket, rail and carrier interfaces before approving a replacement.

What photographs are useful?

Provide a side view of several pitches, an end view showing roller or hollow-pin position, the sprocket and the rail/contact surface. Add the model marking if it is still readable.

What should a new-system RFQ include?

Send carrier/load data, conveyor length and speed, process sequence, strand spacing, rail concept, drive/take-up layout, quantity and environment.

What should a replacement RFQ include?

Send installed model, measured dimensions, photographs, sprocket data, quantity and any special matched-length, attachment or material requirement.

Review the aliran kerja pemilihan kejuruteraan and application guidance, then use the form below with drawings or marked photographs.

Minta Sebut Harga
Available models

Products in Side Roller Chains